![]() ![]() During free-fall the only force that should be acting upon the object is the earth’s gravitational pull (9.8 m/s/s) therefore the velocity of the object should always equal 9.8 m/s/s. ![]() Therefore, the data collected was very accurate. The purpose of the Picket Fence Free Fall Lab was to examine the acceleration of objects as they fall to earth. The accuracy and the precision of these two methods will then be compared. In both methods, the acceleration of gravity will be measured using Atwood’s Machine. The percent error between the average acceleration in the six runs and the accepted value for gravity was only 1.018%. Measuring Acceleration Using Photogates and Hand Timers In this section of the lab, photogate and hand timers are used to time the falling mass. The maximum and minimum accelerations only varied 0.10. The results of this experiment were extremely consistent. For temporary you anger the acceleration due for Earth's gravity g and you found it. Does mass change the acceleration of list object if gravity is novelty only force acting. This proves that none of these circumstances had any effect on the acceleration of the fence and that only gravity influenced its fall. There is likely, the acceleration gravity lab is acceleration to mount the resistanceto being measured and practice trials to drop the group to. During the 6 runs, the picket fence was dropped from the same height and had an average acceleration of 9.82 m/s/s– which is extremely close to the expected value of 9.8 m/s/s. The results of the experiment confirmed the theory that objects will fall with a constant acceleration equal to g (9.8 m/s/s). In this lab the picket fence was dropped repeatedly through a photogate connected to Logger Pro, which allowed the fence’s acceleration and velocity to be recorded and graphed. During free-fall the only force that should be acting upon the object is the earth’s gravitational pull (9.8 m/s/s), therefore the velocity of the object should always equal 9.8 m/s/s. Record your results in the Data Sheet of your Lab Report. ![]() The purpose of the Picket Fence Free Fall Lab was to examine the acceleration of objects as they fall to earth. acceleration due to gravity by measuring the time of fall of a picket fence dropped through a. Variations in G from sea level to the mountains are very small and can be ignored. Other factors that cause acceleration to vary is the radius of the earth at different points. Gravity decreases with altitude, since greater altitude means greater distance from the Earth’s center. Throwing the picket fence upward would also change the velocity and time but not the acceleration.Ĥ.Adding air resistance would change the results.ĥ.The altitude affects the acceleration due to gravity because the closer you are to the center (of earth), there’s more gravity. Extensions:ġ.G (acceleration) is determined in the data charts above.Ģ.Dropping the picket fence from higher above would change the time, and velocity, but it wont change the acceleration.ģ.Throwing the picket fence downward would change the velocity and time, but not the acceleration due to gravity. time graph in graphs.Ĩ.The average acceleration is the same with the acceleration vs. time graph.Ħ.The accepted value for g (gravity) is 9.8 m/s/s, and all the calculated accelerations from the first six runs are within.ħ.Prediction for acceleration vs. time graph because the acceleration is constant which means a straight line of the velocity vs. It is not a parabolic shape like that of the position vs. time graph for free fall would be a parabola because the velocity increases.ģ.The shape of the velocity vs. Analysis Questions:ġ.The minimum, maximum, and average values for acceleration are in the data table.Ģ.The shape of the position vs. time graph is a linear line.ģ.The initial velocity of an object does not have anything to do with its acceleration due to gravity. 0.10/9.82= 0.01018ġ.The additional information I need to determine the average speed of the Picket Fence as it moves through the Photogate is the amount of time need to go through it.Ģ.If an object is moving with constant acceleration, the shape of its velocity vs. After you take that result and multiply by 100. In order to find the precision, take the difference between the minimum and maximum accelerations (0.10 m/s^2) and divide that with 9.82 (the average acceleration). Measuring g by free fall experiment lab report.To get the average acceleration, you take the minimum and maximum accelerations and divide by 2.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |